Shrink and process of the crack on the facades of buildings, cracks in the ceiling and walls in the interiors of apartments and offices, cracks in the joints of gypsum board, crack ... crack ... crack ... This issue takes a lot of effort, nerves and time the owners of the premises builders, painters. Shrinkage cracks and technology on the facades of buildings, cracks in the ceiling and walls in the interiors of apartments and offices, cracks in the joints of gypsum board, crack ... crack ... crack ... This issue takes a lot of strength, nerves, and time at the premises owners, builders, painters. Cracks ruin the appearance and facades, and interiors. Especially annoying cracks at the joints of gypsum board, appeared on the newly renovated surface. Causes of fractures are different. Cracks can be static (size does not change) and dynamical (whose size varies for different reasons). Static cracks easier to remove. For the repair of dynamic fracture requires the use of special materials. In selecting materials for the decorative surfaces with cracks also requires a special approach. The program CAPAROL a complex elastic materials class Cap-Elast delivering high-quality and durable solution to repair and finishing of surfaces with cracks. Special elastic putty to fill cracks Cap-Elast Ri? Spachtel ("Ri?" - "Crack" (nemetsk.)) allow you to easily and securely seal the crack. Reinforcing primer Fibrosil, highly elastic paint PermaSilan, Cap-Elast Phase 1 and Phase 2 will help you paint the surface and provide long-term reinforcement and the overlap of the fractured surfaces. Technical Documentation System Cap-Elast describes the technological schemes that are effective to repair virtually any surface. This article describes some common problems with cracks and methods for their removal. 1. Certain structural cracks. To repair these cracks, resulting in masonry, concrete, plasterboard joints, etc. recommended the following approach: embroider a crack on the width of 1 cm and 1 cm depth in the form of a letter U (Fig. 1), thoroughly cleaned of dust, and primed to saturation Dupa-grund or Caparol Tiefgrund TB (Fig. 2), fill to level the surface material Cap-elast Ri? spachtel (Fig. 3) and well dried. When repairing drywall is recommended before application of Cap-elast Ri? Spachtel primed surface material Caparol-Putzgrund; completes the treatment to fulfill elastic paint Cap-Elast Phase 2 or PermaSilan (for demonstration of high-elastic properties of this material, we apply it to cardboard and subjected to various deformations, painted surface at the same time remained a whole), Muresko, AmphiSilan; Fig. 1. Prepare to repair cracks in Fig. 2. Priming Fig. 3. Filling the crack filler Cap-Elast 2. When fine cracks close to the surface, and cracks that occur during shrinkage and drying out the plaster or concrete, we recommend priming the surface material to perform Caparol Tiefgrund TB or Dupagrund and two-layer elastic cause paint Cap-Elast Phase 2 or PermaSilan. To obtain a surface with a light structure, a special reinforcing paint Fibrosil. This material contains a fiber reinforcement of the crack, and allows you to create a beautiful structural surface. 3. If cracks in the seams and cracks in the concrete surface is recommended to perform surface coating material Dupagrund, as the first layer apply Fibrosil or Cap-Elast Phase 1 and as the final - Cap-Elast Phase 2 or PermaSilan. 4. In order to avoid the appearance of cracks in the joints of gypsum boards recommend priming the surface zashpatlevannyh junction perform special material Caparol Tiefgrund TB. This treatment will reliably protect joints from water penetration, and consequently will not give vozmodnosti emergence and development of cracks. More complex options should be considered in detail in each case. It should be noted that all these materials are one system, provide a lasting solution that guarantees a beautiful view of the facade and interior and has earned his high popularity. Source: http://www.vashdom.ru/articles/stroy-club_1.htm
No comments:
Post a Comment