Hanging sliding door

This is a good choice for modern homes, where the rooms are small and, therefore, the walls are in short supply. Passage from the kitchen into the dining room is often connects two small rooms. Therefore, the standard hinged doors are awkward. Existing panel doors can be easily converted into sliding, if you use one of the many available types of special equipment. If doorways are wide enough, the suit design for double opening in both sides of the doors. This is a good choice for modern homes, where the rooms are small and, therefore, the walls are in short supply. Passage from the kitchen into the dining room is often connects two small rooms. Therefore, the standard hinged doors are awkward. Existing panel doors can be easily converted into sliding, if you use one of the many available types of special equipment. If doorways are wide enough, the suit design for double opening in both sides of the doors. Sold and the new panel doors for interiors. Fixtures are available with all necessary fittings - guides, pendulum bolts, supports, lower rail, stops and screws. But the mounting brackets to secure the guides must be purchased separately. You will need to strap to secure the guide. Before you buy a device for sliding doors, measure the door. The length of the guide should be twice the width of the door. Device must meet weight and your door. If you use an existing door, close the door frame strap quarter to reduce some of the opening. It is better for finishing and also to protect from drafts. Remove the casing and baseboard to the wall, along which moves the door, and then will treat this section of the wall. Installation ends hitch accessories. And finally, the entire structure can close the special decorative panel. You can buy it or do it yourself. The design of the sliding door. In the design shown here sliding doors on top carriers fastened to the edge of the door. In the bottom door along its entire length is cut by a groove, which includes a short lower track - "Slipper". "Slipper" stabilizes the lower edge of door movement. Carriers are inserted into the swing pins, attached to the plastic wheels are put on the top track. The very same guide bracket attached to the base plate. Stoppers at the ends of limiting the course of wheel blocks, and, hence, the door to a whole. The handle is embedded in the door. Installing sliding door 1. Preparation of the door. Remove the door. Dismantle the handles and hinges. Select a groove in the bottom door on the size specified by the manufacturer. Put the door on a pair of goat and mark the position of each carrier on the top door. Awl hole through the tree, and then through the slits in the media, screw them to the upper end. 2. Mounting support bracket. Cut a strip the size specified by the manufacturer, and 50 mm longer than the guide. Put the bar on the box and drill pilot holes. Attach the strap over the opening. She should speak with one edge of the entire length of the door. While an assistant holds the bar with a level against the wall, you will be perforated with holes in places where the strap is finally secured. Remove the bar dosverlite holes and drive in traffic jams in them. Put the bar again, and attach it with screws of appropriate size. 3. How to hang a top track. Utaplivaemye using screws and nuts SELF, screw the bracket to the rail. Place the guide in the supporting plate. Center guide should coincide with the edge of the opening, toward which the door is moving. Assistant keeps track and you marking drills holes in the bracket, respectively, holes in the brackets. After fixing the rail in place, insert it on one wheel blocks. 4. How to hang a door. Assistant holds the door vertically at the track and you at this time move your wheel blocks along a guide so that each block stood in front of the media. Slightly lift the door and one Insert your head bolts into the slots of carriers and lightly screw the nut on the media. Then tap the wedges under the door to lock it. Ensure that the distance to the floor meets the standard specified by the manufacturer. Adjust the course of the door, tighten the nut wrench. Remove the wedges. 5. ATTACHMENT shoe. Carefully move the door in the open position, while making sure that it does not jumps from the guides. Put the shoe on the floor at the side of the opening. Check whether it is a groove in the bottom door. Awl mark the holes in the floor and attach the shoe to the floor. If the floor tile, drill drill and drive in traffic jams in them. 6. Installation obstacles. Assemble the rubber stoppers and support plate screws. Insert your stopper at each end of the guide in place of fixing of the door. Then, firmly tighten the screws. Thus, the stopper in place. Ural LTD