How to check the fit. Insert the door to the box, connecting the hinge edge of the jamb. The gap between the door and the frame on the sides and top should not exceed 2 mm and 4 mm between the lower edge of the door and the floor. If the door is a little wide or long, then secure it and podstrogayte bottom or side edge. 1. How to check the fit. Insert the door to the box, connecting the hinge edge of the jamb. The gap between the door and the frame on the sides and top should not exceed 2 mm and 4 mm between the lower edge of the door and the floor. If the door is a little wide or long, then secure it and podstrogayte bottom or side edge. 2. How to mark the nest for loops. Draw a line across the hinge-end of the door at a distance of 150 mm from the top. Attach a loop to the line and at the same end mark the bottom edge of the loop. The gauge, put a distance between the edge of the hinge plate and the middle of the loop, Draw a line from the front of the doors on its ends by combining two previously deposited line. Now put the gauge at a distance equal to the thickness of the hinge plate, and put the distance at the front of the door. Check the site for the next loop at a distance of 225 mm from the bottom edge of the door the same way. If need be, mark the location for the third loop between the first two. 3. How to make a dimple. Take a chisel with the beveled edge of the same width as the groove. Put the chisel bevel toward uglublyaemoy parts across the deepening of 2 mm from the edge and swipe mallet to cut through the canvas door to a depth equal to the thickness of the hinge plate. Do the same at the other end of the markup. Then place the blade of a chisel deposited at the end of a line parallel to the front side of the door, and fetches toward her. Hold the chisel bevel down at an angle of 45 degrees across the recess. By chisels hit by sharp blows. Then turn the chisel bevel up, put it on the line, deposited on the front of the door, and pick the wood towards the rear boundary of the recess. After that put the chisel vertically and cut down on the upper and lower marks to the edge trim and clean the grooves. Do the same with the other grooves. Door goats to facilitate simple device called a door goats can be assembled from several pieces of junk wood and cardboard. With their help, it is convenient to hold the door in place, if it should podstrogat by size or choose a looped slot. Goats do three small pieces of wood (50 by 25 mm) and two large (150 by 50 mm). Two large bars of 12 mm more than the thickness of the door, nailed to the cross bars 50 to 25 mm. Cardboard strip protects the door surface from damage during operation. A pair of bars (50 by 25 mm), nailed across the bottom of the assembly is stand and lifts the building above the floor. The door of her weight presses a flexible bar (50 by 25 mm), pulls together great blocks, which are firmly holding the door. 4. How to hang a door. Place the fold hinge in the top slot, schedule Punch awl or hole for the screws and fasten the hinge screws are the right size. Attach the remaining loops in the same way. Put a door in a box, then tap the bottom wedges and put a markup of two loops on the jamb. Mark, and then deepen to hinge jamb in the same way as in the doors, then hold the door wedges, attach the wing hinges to the jamb with screws. 5. Partitioning the spindle lock and a keyhole. Make a horizontal mark on the trailing end of the door at a height of one meter from the floor (the height can be varied as you wish). Put the lock body to hold the line and mark the lower edge. Spread the strips on the gauge thickness of the castle and draw two parallel lines perpendicular to the two horizontal, which pass through the center of the face of the door (box figure). Put in the gauge length equal to the distance between the front part of the latch and the center of the hole for the spindle, press the gauge to the edge of the door and hang a lock on the dimensions of both faces of the door. Mark the position of the keyhole. Spend the last vertical line centered between the prior vertical lines. 6. Drilling holes for the spindle and keyhole. Choose a drill diameter, the spindle could easily rotate in the hole. Put the drill on the layout (front side doors) and to fix the door, drill through it. Repeat on the other hand, the hole was finished appearance. Hole for the keyhole is drilled the same way. 7. Boring nest under lock and key. Pick up the drill diameter equal to the thickness of the lock. Measure the length of the lock on the drill bit and wrap in this place with insulating tape, as the depth stop. Drill a series of holes on the line marking the nest for the lock box. Chisel and hammer to tap and clean out the nest of the castle and the trim edge. 8. Mounting the lock and handles. Insert the lock body in the slot and mark the end of the door lock dimensions. Reinsert the lock in the slot and mark the location for screws. Screw the lock included screws. Push the spindle through the square hole in the lock, which is located in front of the drilled holes on the front door, then put the lining for pens, pens themselves and secure with screws. 9. Fixing the host lining. Close the door and mark the position of the tongue on the jamb. Open the door, hang on the tongue pad and measure the distance from the edge of lining up the front of the door. Transfer this distance on the jamb. Attach the pad to host the marks and draw it in pencil. Take a chisel to deepen lining, then mark the holes for screws and screw the cover plate to the jamb. Chisel, do the slots under the tongue and the latch. Fold the tab on the pad with a hammer, it serves as a guide for the tongue. Measure, cut and fasten the door and jamb stops. Ural LTD
No comments:
Post a Comment